KZR's Bikes of the Month for 2024

Installing gas cap

  • Robb2018
  • Topic Author
  • Offline
  • User
  • 76 KZ900 73 Z1 A
More
31 Aug 2021 14:27 #854659 by Robb2018
Installing gas cap was created by Robb2018
I've been trying all morning to install the gas cap on a new tank on my Z1. The latch part makes no sense to me whatsoever.  I figured out one leg of the spring has to go in the groove in the latch but with no instructions It's really hard to figure out.  I've tried putting the spring in both ways and when I'm finally done struggling with it, the pin is going through the spring and it seems to be in place but there's no spring action on the lever. I'm sure someone's run into this problem.  Usually in situations like this after struggling long enough it usually works itself out but I just recently threw my hands in the air and gave up. Any suggestions would be greatly appreciated.  

KZ900; Z1

Please Log in or Create an account to join the conversation.

  • Robb2018
  • Topic Author
  • Offline
  • User
  • 76 KZ900 73 Z1 A
More
31 Aug 2021 14:54 - 31 Aug 2021 14:56 #854660 by Robb2018
Replied by Robb2018 on topic Installing gas cap
So.... yeah, I figured it out.  You have to put one leg of the spring in the groove in the latch, then you have to bend the other leg around so the spring's compressed.  So I did that, still quite the juggling act, had a small nail in one side and as I was pulling it out I lowered the latch so the holes lined up and was sliding the pin in from the other side.... and ZING.... yeah, the spring took off across the garage and landed in the worst possible place I could imagine it landing in, a total black hole for small parts.  UGGGGGGH!!!  Kind of funny actually.  I really should have anticipated this. Anyway, I could spend the rest of my life looking for that spring but will dedicate about an hour to it and unless a miracle happens will have to order a new one, if in fact they are even available.

KZ900; Z1
Last edit: 31 Aug 2021 14:56 by Robb2018.

Please Log in or Create an account to join the conversation.

  • SWest
  • Offline
  • Sustaining Member
  • 10 22 2014
More
31 Aug 2021 15:11 #854662 by SWest

Please Log in or Create an account to join the conversation.

  • Robb2018
  • Topic Author
  • Offline
  • User
  • 76 KZ900 73 Z1 A
More
31 Aug 2021 16:31 #854665 by Robb2018
Replied by Robb2018 on topic Installing gas cap
Last I saw of it, it was heading towards a place that had two big boxes full of junk and about a million nooks and crannies outside the boxes. I just spent an hour looking and I don't think I could find it if my life depended on it.  So I guess I have to either find a replacement or make one. 

 

KZ900; Z1

Please Log in or Create an account to join the conversation.

More
31 Aug 2021 17:23 #854668 by Mikaw
Replied by Mikaw on topic Installing gas cap
No eBay APP ID and/or Cert ID defined in Kunena configurationYou will trip over it as your walking back into the garage after picking up the new one from the mail box. Happens all the time to me. 

Appears to be a separate part.  www.partzilla.com/product/kawasaki/51053...94080b52969d3847fdf8


1976 KZ 900 A4 kzrider.com/forum/11-projects/613548-1976-kz-900-a4
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.

Please Log in or Create an account to join the conversation.

More
31 Aug 2021 18:38 #854670 by 750 R1
Replied by 750 R1 on topic Installing gas cap

You will trip over it as your walking back into the garage after picking up the new one from the mail box. Happens all the time to me. 

Never a truer word spoken......!!!!!!!!!!!!!!!!!!!!!!!!

Please Log in or Create an account to join the conversation.

  • SWest
  • Offline
  • Sustaining Member
  • 10 22 2014
More
31 Aug 2021 20:26 - 31 Aug 2021 20:27 #854672 by SWest
Replied by SWest on topic Installing gas cap
That little bugger can go sproiiiiing anywhere. 
Steve
Last edit: 31 Aug 2021 20:27 by SWest.

Please Log in or Create an account to join the conversation.

  • Robb2018
  • Topic Author
  • Offline
  • User
  • 76 KZ900 73 Z1 A
More
07 Sep 2021 16:34 #854973 by Robb2018
Replied by Robb2018 on topic Installing gas cap
No eBay APP ID and/or Cert ID defined in Kunena configuration

You will trip over it as your walking back into the garage after picking up the new one from the mail box. Happens all the time to me. 

Appears to be a separate part.  www.partzilla.com/product/kawasaki/51053...94080b52969d3847fdf8


 
Yeah probably will but thanks for the part number. Ebay had one for 4 bucks.  Wasn't worth 4 bucks tearing the garage apart looking for it. 

KZ900; Z1
The following user(s) said Thank You: Mikaw

Please Log in or Create an account to join the conversation.

More
17 Oct 2021 20:34 #856769 by Elfarm98648
Replied by Elfarm98648 on topic Installing gas cap
As does happen, I was in the same situation. Lost mine, threw a pen spring in it, then sure enough once it was remounted and working, found the original one. Funny thing is, the pen spring worked better than the original one! So I still have the original spring sitting stashed away. 

Please Log in or Create an account to join the conversation.

More
20 Apr 2023 08:18 - 20 Apr 2023 10:15 #883480 by Moose1800
Replied by Moose1800 on topic Installing gas cap
I could use some help with this guys if you would be so kind.

Before I start driving these pins in above my freshly painted tank I need to know where each one goes. I'll post a pic of what came with the cap,It came with three pins shown below, #1 is a roll pin, #2 is a solid pin just a tad shorter than the roll pin and #3 is a shorter pin that is knurled on one end and serrated on the other end.

It's my thinking that #1 is used to mount the cap to the tank and #3 is for the other end of the cap for the latch to grab if so is the #2 pin just supplied to help drive the pins in place?

[img

 
Last edit: 20 Apr 2023 10:15 by Moose1800.

Please Log in or Create an account to join the conversation.

  • Wookie58
  • Away
  • Moderator
More
20 Apr 2023 08:28 #883481 by Wookie58

Please Log in or Create an account to join the conversation.

More
20 Apr 2023 09:04 #883482 by Moose1800
Replied by Moose1800 on topic Installing gas cap
Thanks Wookie, Unfortunately that's for the locking cap that needs only one pin the cap I have is a repop Z1 cap with no lock just a latch.

Please Log in or Create an account to join the conversation.

Powered by Kunena Forum

If you like KZR Please consider making a donation. Thank you.

KZRider is free, but not without cost.

Please consider chipping in a few bucks to help cover the cost of running the KZR servers.