- Posts: 11
- Thank you received: 0
Suspension lowering?
- GrumpyBSTRD
- Topic Author
- Offline
- User
With the OEM seat she doesn't come close to touching the ground so I removed the seat and put a piece of 1" foam on the frame to test it and she barely touches with her toes.
So I will be putting a "low rider" seat on but still need to get it 3" lower.
My question is, what is the easiest/cheapest way to safely do so?
I have seen a number of these bikes with the rear shocks replaced with a solid steel bar but I prefer to keep it a soft tail.
Please Log in or Create an account to join the conversation.
- TexasKZ
- Offline
- Platinum Member
- Posts: 7592
- Thank you received: 2243
You are right about the struts. They will make theride so harsh that shemaynever ride again.
Three inces is a bunch, but you maybe able to getclose by a combination of a thinner seat, shorter shocks and raising the forks. You will want to be absolutely sure that neither tire will hit anything when the suspension is fully compressed.
You should be able to find some shocks that are an inch or inch and a half shorter and may be able to raise the forks an inch. She may haveto settle for tiptoe one one foot at a time.
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough
Please Log in or Create an account to join the conversation.
- SWest
- Offline
- Sustaining Member
- 10 22 2014
- Posts: 23044
- Thank you received: 2763
Steve
Please Log in or Create an account to join the conversation.
- SWest
- Offline
- Sustaining Member
- 10 22 2014
- Posts: 23044
- Thank you received: 2763
Please Log in or Create an account to join the conversation.
- GrumpyBSTRD
- Topic Author
- Offline
- User
- Posts: 11
- Thank you received: 0
I've been looking at the rear shock and noticed the coils are in 2 peices. 1 larger section that seems to have all the travel and a shorter (about 1 1/2") section that is so tight appears to be only there to add length. I may remove it and see if I can bottom it out by jumping on it, then go from there.
Please Log in or Create an account to join the conversation.
- SWest
- Offline
- Sustaining Member
- 10 22 2014
- Posts: 23044
- Thank you received: 2763
Steve
Please Log in or Create an account to join the conversation.
- Patton
- Offline
- KZr Legend
- Posts: 18640
- Thank you received: 2098
High heel boots also help.
Good Fortune!
1973 Z1
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Tyrell Corp
- Offline
- User
- "You were made as well as we could make you"
- Posts: 1650
- Thank you received: 261
Lifting the rear end sharpens the steering, and vice cersa. ..hence my suggestion doing back and front together by the same amount, then dropping the front gradually and seeing how it feels.
Custom style bikes have wide frame castor angles for straight line stability, a modern sports bike runs much tighter castor angle for quick steering. You probably have plenty of range of adjustment here on that bike.
Lowering the front more than the back would give lighter and quicker steering which might also be an improvement, if not overdone. If you put an inch thick plank of wood under the rear tyre you can actually feel the difference by just turning the bars whilst sitting on it: although it brings the weight distribution further forward so there is more weigh on the front, the sharper castor angle makes it feel slightly lighter to turn the bars.
I'm 6'4 tall so generally go for longer rear shocks where I can.
1980 Gpz550 D1, 1981 GPz550 D1. 1982 GPz750R1. 1983 z1000R R2. all four aces
Please Log in or Create an account to join the conversation.
- GrumpyBSTRD
- Topic Author
- Offline
- User
- Posts: 11
- Thank you received: 0
Patton wrote: Could also consider Honda Rebel and Suzuki Savage, which have very low stock seat heights, and are good reliable bikes that can keep up with traffic.
The Rebel 450 was my first choice but couldn't find one within budget. I picked up the KZ for next to nothing due to engine issues (but that's for another forum :rolleyes: )
I just removed the smaller of the coils on both sides and by the time I cut the seat down should be about right. Even with my fat 225lb rear jumping on it still only squatted a couple inches.
But will definitely need shorter shocks though, when these shocks extend to top out they exceed the length of the coils and risk loosing the keepers.
Please Log in or Create an account to join the conversation.
- martin_csr
- Offline
- User
- Posts: 8068
- Thank you received: 1656
Edit: eebbaayy item links are not visible on my Mac computer using Apple Safari. doh.
Item # 221585175841
Item # 380470596619 (these may be too short - rear tire fender clearance - see Patton's reply below)
Please Log in or Create an account to join the conversation.
- Tyrell Corp
- Offline
- User
- "You were made as well as we could make you"
- Posts: 1650
- Thank you received: 261
Maybe make a pair of struts to temporarily hardtail it and experiment with ride height and see howthe steering and clearance feels.
1980 Gpz550 D1, 1981 GPz550 D1. 1982 GPz750R1. 1983 z1000R R2. all four aces
Please Log in or Create an account to join the conversation.
- Patton
- Offline
- KZr Legend
- Posts: 18640
- Thank you received: 2098
One way to measure is to test clearance with only one of the two rear shocks attached, which helps assure being able to achieve maximum collapse of the rear end.
Can also put a ball of modeling clay on top of the rear tire when compressing the rear suspension to measure the clearance at full compression.
Besides the specter of ripping out under-fender wiring, hitting a large bump or pothole that unexpectedly bottoms out the rear suspension might cause loss of control, especially by a novice rider.
Good Fortune!
1973 Z1
KZ900 LTD
Please Log in or Create an account to join the conversation.