Sprockets

  • ellwinger
  • ellwinger's Avatar Topic Author
  • Offline
  • User
  • Posts: 19
  • Thanks: 1

Sprockets

11 Jul 2023 09:56
#887112
My KZ650H runs great but tops out at 55 mph and 4000 rpm.  That seems like the rpms are WAY to high and it needs to be geared down. Am I wrong?

Please Log in or Create an account to join the conversation.

  • Wookie58
  • Wookie58's Avatar
  • Away
  • Moderator
  • Posts: 4559
  • Thanks: 2707

Re: Sprockets

11 Jul 2023 10:01
#887113
When you say it “tops out” what do you mean? Are you saying it won’t go anymore in any gear?

Please Log in or Create an account to join the conversation.

  • Nessism
  • Nessism's Avatar
  • Offline
  • Sustaining Member
  • Posts: 7559
  • Thanks: 2920

Re: Sprockets

11 Jul 2023 11:00
#887117
4000 rpm at 55 mph sounds about right.  The engine is built to REV, so rev it and enjoy!

Please Log in or Create an account to join the conversation.

  • ellwinger
  • ellwinger's Avatar Topic Author
  • Offline
  • User
  • Posts: 19
  • Thanks: 1

Re: Sprockets

11 Jul 2023 12:25
#887119
Doesn't 55mph seem a little slow? It won't rev higher than that.

Please Log in or Create an account to join the conversation.

  • Wookie58
  • Wookie58's Avatar
  • Away
  • Moderator
  • Posts: 4559
  • Thanks: 2707

Re: Sprockets

11 Jul 2023 13:28
#887120
If it won't rev past 4000 then that is a totally different issue

Please Log in or Create an account to join the conversation.

  • Nerdy
  • Nerdy's Avatar
  • Offline
  • Sustaining Member
  • Posts: 1046
  • Thanks: 410

Re: Sprockets

11 Jul 2023 13:56
#887121
NOW IS THE TIME ON SPROCKETS WHEN WE DANCE!!

1979 KZ400 Gifted to a couple of nephews
1967 Yamaha YCS1 Bonanza
1980 KZ440B
1981 Yamaha XT250H
1981 KZ440 LTD project bike
1981 GPz550
2013 Yamaha FZ6R
The following user(s) said Thank You: sf4t7

Please Log in or Create an account to join the conversation.

  • Nerdy
  • Nerdy's Avatar
  • Offline
  • Sustaining Member
  • Posts: 1046
  • Thanks: 410

Re: Sprockets

11 Jul 2023 13:58
#887122
If it won't rev past 4000 then that is a totally different issue
 

Could the ignition advancer be hanging up (i.e. not advancing)?
1979 KZ400 Gifted to a couple of nephews
1967 Yamaha YCS1 Bonanza
1980 KZ440B
1981 Yamaha XT250H
1981 KZ440 LTD project bike
1981 GPz550
2013 Yamaha FZ6R

Please Log in or Create an account to join the conversation.

  • Injected
  • Injected's Avatar
  • Offline
  • User
  • Posts: 1166
  • Thanks: 646

Re: Sprockets

11 Jul 2023 14:02
#887123
My KZ650H runs great but tops out at 55 mph and 4000 rpm.  That seems like the rpms are WAY to high and it needs to be geared down. Am I wrong?
 
A good running 650 four cylinder should "top out" at 110MPH @ 9000 RPM.
1978 KZ650B2 w 1197cc Z1 engine
1977 KZ650B1 w 750cc Spectre engine
1979 KZ650C3 w 831cc Hot Rod engine
1978 KZ650C2 w 762cc DFI project
1977 KZ650C1 stock restoration project
1978 KZ650B2 modified project
1978 KZ650B2 Injected Drag 831cc
1980 Z1 Custom Frame Drag 1327cc
1981 Z50R Honda tow bike
The following user(s) said Thank You: ellwinger

Please Log in or Create an account to join the conversation.

  • martin_csr
  • martin_csr's Avatar
  • Offline
  • User
  • Posts: 8019
  • Thanks: 1645

Re: Sprockets

12 Jul 2023 08:44 - 13 Jul 2023 08:00
#887148
Assuming you have an 85mph speedometer, a 650-CSR should be able to peg the needle no problem with power to spare.

Make sure the battery is good and fully charged. I would do a load test. 

Ignition coils. ride the motorcycle at speed, then stop & feel them. don't get burned by the valve cover.
The ignition coils should get warm, not hot.  Mine were very hot to the touch, so I got new Dyna coils. 

Clean, check & lubricate the timing advancer. make sure the springs & stuff are good and not rusted or damaged or anything. 
Separate the rotor from the body while servicing & fill the groove w grease. Afterwards, operate the advancer by hand >> the rotor should snap back when released. This stuff is in the manual.  
Last edit: 13 Jul 2023 08:00 by martin_csr.

Please Log in or Create an account to join the conversation.

  • TexasKZ
  • TexasKZ's Avatar
  • Offline
  • Platinum Member
  • Posts: 7739
  • Thanks: 2356

Re: Sprockets

12 Jul 2023 08:47
#887149
Has all of the routine maintenance listed in the owner’s manual and the factory service manual been performed  recently? If you are not 100% sure about any item on the list, I would start at the top and do each and every item as listed. In the process, you are quite likely to find the problem, and when you finish the list, you can be sure the bike is performing as designed. Following the schedule will insure that you have a well-running, reliable ride.
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough

www.kzrider.com/11-projects/620336-anoth...uild-thread?start=24
The following user(s) said Thank You: Wookie58

Please Log in or Create an account to join the conversation.

  • ellwinger
  • ellwinger's Avatar Topic Author
  • Offline
  • User
  • Posts: 19
  • Thanks: 1

Re: Sprockets

14 Jul 2023 20:12
#887225
Advancer works great. seems like it gets no gas above 55.

Please Log in or Create an account to join the conversation.

  • ellwinger
  • ellwinger's Avatar Topic Author
  • Offline
  • User
  • Posts: 19
  • Thanks: 1

Re: Sprockets

14 Jul 2023 20:15
#887226
Everything checks out. Doesn't seem to be getting enough gas above55.

Please Log in or Create an account to join the conversation.

Powered by Kunena Forum