Sprockets
- ellwinger
-
Topic Author
- Offline
- User
- Posts: 19
- Thanks: 1
Sprockets
11 Jul 2023 09:56
My KZ650H runs great but tops out at 55 mph and 4000 rpm. That seems like the rpms are WAY to high and it needs to be geared down. Am I wrong?
Please Log in or Create an account to join the conversation.
- Wookie58
-
- Offline
- Moderator
- Posts: 4559
- Thanks: 2707
Re: Sprockets
11 Jul 2023 10:01
When you say it “tops out” what do you mean? Are you saying it won’t go anymore in any gear?
1982 KZ1000 Ltd
www.kzrider.com/forum/11-projects/617631...-82-begins?start=192
kzrider.com/filebase-alias?view=download...d-fault-diagnosis&ca
www.kzrider.com/forum/11-projects/617631...-82-begins?start=192
kzrider.com/filebase-alias?view=download...d-fault-diagnosis&ca
Please Log in or Create an account to join the conversation.
- Nessism
-
- Offline
- Sustaining Member
- Posts: 7559
- Thanks: 2920
Re: Sprockets
11 Jul 2023 11:00
4000 rpm at 55 mph sounds about right. The engine is built to REV, so rev it and enjoy!
Ed
Carb O-ring Kits : www.kzrider.com/forum/3-carburetor/61807...-o-ring-kits?start=0
www.kzrider.com/forum/faq-wiki/618026-new-owner-things-to-know
1981 KZ750E2
www.kzrider.com/forum/11-projects/604901...z750e-project-thread
Carb O-ring Kits : www.kzrider.com/forum/3-carburetor/61807...-o-ring-kits?start=0
www.kzrider.com/forum/faq-wiki/618026-new-owner-things-to-know
1981 KZ750E2
www.kzrider.com/forum/11-projects/604901...z750e-project-thread
Please Log in or Create an account to join the conversation.
- ellwinger
-
Topic Author
- Offline
- User
- Posts: 19
- Thanks: 1
Re: Sprockets
11 Jul 2023 12:25
Doesn't 55mph seem a little slow? It won't rev higher than that.
Please Log in or Create an account to join the conversation.
- Wookie58
-
- Offline
- Moderator
- Posts: 4559
- Thanks: 2707
Re: Sprockets
11 Jul 2023 13:28
If it won't rev past 4000 then that is a totally different issue
1982 KZ1000 Ltd
www.kzrider.com/forum/11-projects/617631...-82-begins?start=192
kzrider.com/filebase-alias?view=download...d-fault-diagnosis&ca
www.kzrider.com/forum/11-projects/617631...-82-begins?start=192
kzrider.com/filebase-alias?view=download...d-fault-diagnosis&ca
Please Log in or Create an account to join the conversation.
- Nerdy
-
- Offline
- Sustaining Member
- Posts: 1046
- Thanks: 410
Re: Sprockets
11 Jul 2023 13:561967 Yamaha YCS1 Bonanza
1980 KZ440B
1981 Yamaha XT250H
1981 KZ440 LTD project bike
1981 GPz550
2013 Yamaha FZ6R
The following user(s) said Thank You: sf4t7
Please Log in or Create an account to join the conversation.
- Nerdy
-
- Offline
- Sustaining Member
- Posts: 1046
- Thanks: 410
Re: Sprockets
11 Jul 2023 13:58If it won't rev past 4000 then that is a totally different issue
Could the ignition advancer be hanging up (i.e. not advancing)?
1967 Yamaha YCS1 Bonanza
1980 KZ440B
1981 Yamaha XT250H
1981 KZ440 LTD project bike
1981 GPz550
2013 Yamaha FZ6R
Please Log in or Create an account to join the conversation.
- Injected
-
- Offline
- User
- Posts: 1166
- Thanks: 646
Re: Sprockets
11 Jul 2023 14:02A good running 650 four cylinder should "top out" at 110MPH @ 9000 RPM.My KZ650H runs great but tops out at 55 mph and 4000 rpm. That seems like the rpms are WAY to high and it needs to be geared down. Am I wrong?
1978 KZ650B2 w 1197cc Z1 engine
1977 KZ650B1 w 750cc Spectre engine
1979 KZ650C3 w 831cc Hot Rod engine
1978 KZ650C2 w 762cc DFI project
1977 KZ650C1 stock restoration project
1978 KZ650B2 modified project
1978 KZ650B2 Injected Drag 831cc
1980 Z1 Custom Frame Drag 1327cc
1981 Z50R Honda tow bike
1977 KZ650B1 w 750cc Spectre engine
1979 KZ650C3 w 831cc Hot Rod engine
1978 KZ650C2 w 762cc DFI project
1977 KZ650C1 stock restoration project
1978 KZ650B2 modified project
1978 KZ650B2 Injected Drag 831cc
1980 Z1 Custom Frame Drag 1327cc
1981 Z50R Honda tow bike
The following user(s) said Thank You: ellwinger
Please Log in or Create an account to join the conversation.
- martin_csr
-
- Offline
- User
- Posts: 8019
- Thanks: 1645
Re: Sprockets
12 Jul 2023 08:44 - 13 Jul 2023 08:00
Assuming you have an 85mph speedometer, a 650-CSR should be able to peg the needle no problem with power to spare.
Make sure the battery is good and fully charged. I would do a load test.
Ignition coils. ride the motorcycle at speed, then stop & feel them. don't get burned by the valve cover.
The ignition coils should get warm, not hot. Mine were very hot to the touch, so I got new Dyna coils.
Clean, check & lubricate the timing advancer. make sure the springs & stuff are good and not rusted or damaged or anything.
Separate the rotor from the body while servicing & fill the groove w grease. Afterwards, operate the advancer by hand >> the rotor should snap back when released. This stuff is in the manual.
Make sure the battery is good and fully charged. I would do a load test.
Ignition coils. ride the motorcycle at speed, then stop & feel them. don't get burned by the valve cover.
The ignition coils should get warm, not hot. Mine were very hot to the touch, so I got new Dyna coils.
Clean, check & lubricate the timing advancer. make sure the springs & stuff are good and not rusted or damaged or anything.
Separate the rotor from the body while servicing & fill the groove w grease. Afterwards, operate the advancer by hand >> the rotor should snap back when released. This stuff is in the manual.
Last edit: 13 Jul 2023 08:00 by martin_csr.
Please Log in or Create an account to join the conversation.
- TexasKZ
-
- Offline
- Platinum Member
- Posts: 7739
- Thanks: 2356
Re: Sprockets
12 Jul 2023 08:47
Has all of the routine maintenance listed in the owner’s manual and the factory service manual been performed recently? If you are not 100% sure about any item on the list, I would start at the top and do each and every item as listed. In the process, you are quite likely to find the problem, and when you finish the list, you can be sure the bike is performing as designed. Following the schedule will insure that you have a well-running, reliable ride.
1982 KZ1000 LTD parts donor
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough
www.kzrider.com/11-projects/620336-anoth...uild-thread?start=24
1981 KZ1000 LTD awaiting resurrection
2000 ZRX1100 not ridden enough
www.kzrider.com/11-projects/620336-anoth...uild-thread?start=24
The following user(s) said Thank You: Wookie58
Please Log in or Create an account to join the conversation.
- ellwinger
-
Topic Author
- Offline
- User
- Posts: 19
- Thanks: 1
Please Log in or Create an account to join the conversation.
- ellwinger
-
Topic Author
- Offline
- User
- Posts: 19
- Thanks: 1
Re: Sprockets
14 Jul 2023 20:15
Everything checks out. Doesn't seem to be getting enough gas above55.
Please Log in or Create an account to join the conversation.