Dyna S Ignition Users - Feedback
- Highway Magician
-
Topic Author
- Offline
- User
- Posts: 80
- Thanks: 33
Dyna S Ignition Users - Feedback
16 Sep 2020 08:43
No eBay APP ID and/or Cert ID defined in Kunena configurationThe igniter on my '82 GPZ1100 has seen better days, so I'm thinking of installing a Dyna S ignition like the one in the link below.
This kit eliminates the factory igniter, right?
I'm looking for feedback from those running this kit. Thanks.
This kit eliminates the factory igniter, right?
I'm looking for feedback from those running this kit. Thanks.
Motorcycle builder since 1973. Master Tech. Current bike: 1982 GPZ1100B2.
Please Log in or Create an account to join the conversation.
- zed1015
-
- Offline
- User
- Posts: 3091
- Thanks: 1645
Re: Dyna S Ignition Users - Feedback
16 Sep 2020 09:22
Yes. Stand alone replacement no igniter required.
Just needs switched power from the ignition switch and 3 to 5 ohm coils.
Been running them for years no issues.
Got them on all my bikes.
Just needs switched power from the ignition switch and 3 to 5 ohm coils.
Been running them for years no issues.
Got them on all my bikes.
AIR CORRECTOR JETS FOR VM CARBS AND ETHANOL RESISTANT VITON CHOKE PLUNGER SEAL REPLACMENT FOR ALL CLASSIC AND MODERN MOTORCYCLE CARBURETTORS
www.kzrider.com/23-for-sale/611992-air-c...lide-mikunis?start=0
www.kzrider.com/23-for-sale/611992-air-c...lide-mikunis?start=0
Please Log in or Create an account to join the conversation.
- hardrockminer
-
- Offline
- Sustaining Member
- Posts: 3010
- Thanks: 1107
Re: Dyna S Ignition Users - Feedback
16 Sep 2020 09:48
I recently converted my 1980 KZ1000 LTD. Runs better than ever!
I have one beef about the Dyna S system. They recommend using their blue splice to attach to a power wire. I've had issues in the past getting the system to power up so I put a standard bullet connector on the red wire and attached it to the double brown femail connector near the headlight. This is a spare 12 volt connection on the main harness.
I have one beef about the Dyna S system. They recommend using their blue splice to attach to a power wire. I've had issues in the past getting the system to power up so I put a standard bullet connector on the red wire and attached it to the double brown femail connector near the headlight. This is a spare 12 volt connection on the main harness.
I have several restored bikes along with a 2006 Goldwing with a sidecar. My wife has a 2019 Suzuki DR 650 for on and off road.
Please Log in or Create an account to join the conversation.
- Mikaw
-
- Offline
- Sustaining Member
- Posts: 4837
- Thanks: 1851
Re: Dyna S Ignition Users - Feedback
16 Sep 2020 11:43
I agree with HRM, upgrade the red power wire, don’t use the scotch lock.
As far as the system, to quote a popular infomercial, “set it and forget it”
As far as the system, to quote a popular infomercial, “set it and forget it”
1976 KZ 900 A4
kzrider.com/forum/11-projects/613548-1976-kz-900-a4
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.
Please Log in or Create an account to join the conversation.
- Kidkawie
-
- Offline
- User
- I bleed premix
- Posts: 1913
- Thanks: 243
Re: Dyna S Ignition Users - Feedback
16 Sep 2020 12:06 - 16 Sep 2020 12:08
Only issue I had on my Z1b was (from what everyone has told me) the pickups are installed backwards from the factory, so when you install them you are maxed out in one direction (I forget which) for timing adjustments. From what I hear its an ongoing problem and I just need to swap pickup locations. I got it timed, but its litterally at the very end of adjustment.
I also plan on soldering the harness instead of depending on those wire taps.
I also plan on soldering the harness instead of depending on those wire taps.
1975 Z1 900
1994 KX250 Supermoto
2004 KX125
1994 KX250 Supermoto
2004 KX125
Last edit: 16 Sep 2020 12:08 by Kidkawie.
Please Log in or Create an account to join the conversation.
- zed1015
-
- Offline
- User
- Posts: 3091
- Thanks: 1645
Re: Dyna S Ignition Users - Feedback
16 Sep 2020 12:15Kidkawie wrote: Only issue I had on my Z1b was (from what everyone has told me) the pickups are installed backwards from the factory, so when you install them you are maxed out in one direction (I forget which) for timing adjustments. From what I hear its an ongoing problem and I just need to swap pickup locations. I got it timed, but its litterally at the very end of adjustment.
I also plan on soldering the harness instead of depending on those wire taps.
You may have the wrong rotor fitted which will cause that problem.
There are two types marked either 3 and 3A.
3A is for the early Z1 rotor and 3 for the later 900/1000 rotor stamped 005.
AIR CORRECTOR JETS FOR VM CARBS AND ETHANOL RESISTANT VITON CHOKE PLUNGER SEAL REPLACMENT FOR ALL CLASSIC AND MODERN MOTORCYCLE CARBURETTORS
www.kzrider.com/23-for-sale/611992-air-c...lide-mikunis?start=0
www.kzrider.com/23-for-sale/611992-air-c...lide-mikunis?start=0
Please Log in or Create an account to join the conversation.
- Highway Magician
-
Topic Author
- Offline
- User
- Posts: 80
- Thanks: 33
Re: Dyna S Ignition Users - Feedback
16 Sep 2020 15:25
OK thanks, it sounds like a winner.
Did you time it using a test light or use a timing light?
I'm close to starting this bike for the first time in 14 years.
Did you time it using a test light or use a timing light?
I'm close to starting this bike for the first time in 14 years.
Motorcycle builder since 1973. Master Tech. Current bike: 1982 GPZ1100B2.
Please Log in or Create an account to join the conversation.
- Mikaw
-
- Offline
- Sustaining Member
- Posts: 4837
- Thanks: 1851
Re: Dyna S Ignition Users - Feedback
16 Sep 2020 17:31
Static time it per install directions and then once started use a timing light and dynamic time.
1976 KZ 900 A4
kzrider.com/forum/11-projects/613548-1976-kz-900-a4
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.
Please Log in or Create an account to join the conversation.
- Mikaw
-
- Offline
- Sustaining Member
- Posts: 4837
- Thanks: 1851
Re: Dyna S Ignition Users - Feedback
16 Sep 2020 17:34 - 16 Sep 2020 17:36
1976 KZ 900 A4
kzrider.com/forum/11-projects/613548-1976-kz-900-a4
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.
Last edit: 16 Sep 2020 17:36 by Mikaw.
Please Log in or Create an account to join the conversation.
- Vorbeck
-
- Offline
- Sustaining Member
- fubar
- Posts: 64
- Thanks: 2
Please Log in or Create an account to join the conversation.
- Bama704
-
- Offline
- User
- Posts: 202
- Thanks: 28
Re: Dyna S Ignition Users - Feedback
17 Sep 2020 06:45
I just put it on my KZ900, with great results. Ditch the blue splice they provide, I wired it in with the wires they suggest but soldered them together instead of the splice.
I static timed mine and am spot on.
I static timed mine and am spot on.
1977 KZ900
Carbs are late model 1975 28mm
Carbs are late model 1975 28mm
Please Log in or Create an account to join the conversation.
- DOHC
-
- Offline
- Sustaining Member
- Those Doe-Hawks really go!
- Posts: 1250
- Thanks: 564
Re: Dyna S Ignition Users - Feedback
17 Sep 2020 07:37zed1015 wrote: and 3 to 5 ohm coils.
As far as I can tell by reading the FSM, the 82 kz1100 has coils with a range of 1.8 to 2.8 ohms, which is too low for the Dyna S. You would need to replace the coils as well.
Otherwise, I have used both the Dyna S and Dyna III and never had any issues with either one. Set and forget.
'78 Z1-R in blue
, '78 Z1-R in black,
'78 Z1-R in pieces
My dad's '74 Z1
'00 ZRX1100
My dad's '74 Z1
'00 ZRX1100
Please Log in or Create an account to join the conversation.