- Posts: 661
- Thank you received: 5
KZ1000 P, handling question
- z1rick
- Topic Author
- Offline
- User
Hey Retro, where do you get your tires balanced? I was thinking about going out to Chaparral in SB to buy the tires, don't know if they balance them or not.
Anaheim CA
1999 KZ 100P
1974 Z1 900 Project
1977 (2) KZ 650 projects
Please Log in or Create an account to join the conversation.
- Patton
- Offline
- KZr Legend
- Posts: 18640
- Thank you received: 2098
(1) Verify rear wheel alignment. Don't place blind faith in the chain adjuster alignment marks. Sight down the chain (eyeball chain for straightness from top of rear sprocket to front sprocket making sure the chain goes straight onto the sprockets without making any sideways turns).
(2) Verify alignment of front wheel with rear wheel. When the front wheel is pointing perfectly straight forward, the rear wheel should also be pointing perfectly straight forward. May use a long straight edge or string (sight down it) to assure this. When coming off sides of the rear tire (from rear end of rear tire) toward the front and on past the front wheel, the straight edge or straight string should be exactly the same slight distance from both sides of the front tire. The straight edge or string won't be up against both the sides of the front tire because of the smaller width tire on the front. If both tires were the same width, the straight edge or string would supposedly be fitting smoothly up against the rear tire sides and front tire sides. (Does this make sense?).
The objective is to assure that both front and rear wheels are perfectly in line with each other and both pointing straight ahead and in line with the bike when motoring straight down the road. Should be able to remove hands from the handlebars and easily steer it with only gentle knee pressure indefinitely along a straight road and with the bike remaining perfectly upright without any sideways lean and without any tendancy to pull one way or another as you motor along.
(3) Loose swing arm bolt (already mentioned) or worn swing arm bearings (bushings in earlier models) may also cause an unstable ride. On centerstand (rear wheel in the air), try to move the rear tire from side and look and listen for any play in the swing arm between the swing arm and the frame.
(4) Confirm both rear shocks adjusted to same preload, and that neither shock is leaking.
(5) Assure forks are equally adjusted in their clamps and are not binding; front wheel fork caps are properly installed and tightened; correct amount and viscosity of fork oil.
(6) As already mentioned -- Assure front wheel bearings are not worn out (or rear wheel bearings).
(7) Has bike ever been dropped? Could result in triple tree (steering head) damage which is sometimes difficult to see by visual examination. Swing arm bent or twisted? Frame bent? Fork bent?
( tires balanced? either wheel bent or warped?
FWIW, I get new mail order tires mounted and balanced at the local Kaw dealer for $25 each wheel and consider it money well spent. And would pay the $35 - $50 charged by other places if necessary. Just hate, hate, hate personally mounting new tires .
1973 Z1
KZ900 LTD
Please Log in or Create an account to join the conversation.
- Zthou1977
- Offline
- User
- Posts: 96
- Thank you received: 0
I believe the P already has tapered steering bearings. If I were you I'd check everything the shop did. I have heard a lot of scary stories of near-accidents because parts were not torqued down right (and coming loose as a result), brakes that were not bled (an especially nasty surprise) etc.
It sounds like you have too much free play somewhere. Start with putting it on the center-stand: lift the front wheel, and try to wiggle it back and forth. Any play? Tighten the steering bolt. If not, check the forks: do they stick? Does the front wheel go side-to-side? Maybe they forgot a washer. Of course you'll need to check your fork-oil as well.
At the rear: grab the swingarm and check for play. Is the swingarm bolt tightened? Is the wheel centered and lined out right? A set of Koni's or so are way better than the original shocks btw, but you'll notice this only when you're pushing the bike, not on the straights at a normal speed like 70mph.
It should be a stable bike.
PS: paint it black and lose the fairing! It's a much better bike that way. The paint really helps.
Post edited by: Zthou1977, at: 2007/03/22 14:47
1977 Z1000A1, 1982-1986 KZ1000P (built from two piles of parts), Moto Martin Z1200 (trying to get it registered), 1977 Z650B1
Utrecht, The Netherlands
Please Log in or Create an account to join the conversation.
- RetroRiceRocketRider
- Offline
- User
- ...bring in the machine that goes PING!
- Posts: 1641
- Thank you received: 29
What I meant by mis-matched, was different brands (Dunlop, Metzler, etc) on the same bike, and/or diff compounds (touring, sport, etc.) on the same bike.Tires do look to be miss-matched, front has "straight grooves", rear has the diagonal grooves, will be getting new rubber soon.
FWIW, the '84 GPz550 I once owned (as well as a lot of other bikes Kawi and the other import Manufacturers produced) came stock with a diagonally treaded rear tire but a ribbed front tire, and they were of the same brand and compound.
z1rick wrote:
There are a few places local that will mount a tire that isn't purchased from them, but I'm not sure if Chapparal cycle is one of them. It's worth a call to check.Hey Retro, where do you get your tires balanced? I was thinking about going out to Chaparral in SB to buy the tires, don't know if they balance them or not.
I did however buy front tires for both Rose's bike and my ZN from them last year, since they had the best deal going locally.
If you take the wheel(s) off your bike and just bring them to Chapparal it only costs about $20 each for mounting and balancing, plus another $2 each for disposal of the old tire.
If the tread on the tire you plan on getting is directional (arrow on sidewall pointing travel direction), be extra sure that they mount it correctly. I had to have them re-mount/re-balance one of the tires we got because the guy goofed and mounted it backwards. :pinch:
Post edited by: RetroRiceRocketRider, at: 2007/03/22 21:09
Please Log in or Create an account to join the conversation.
- z1rick
- Topic Author
- Offline
- User
- Posts: 661
- Thank you received: 5
Anaheim CA
1999 KZ 100P
1974 Z1 900 Project
1977 (2) KZ 650 projects
Please Log in or Create an account to join the conversation.
- z1rick
- Topic Author
- Offline
- User
- Posts: 661
- Thank you received: 5
Anaheim CA
1999 KZ 100P
1974 Z1 900 Project
1977 (2) KZ 650 projects
Please Log in or Create an account to join the conversation.
- Pterosaur
- Visitor
...Oh buy the way, wrenched my back a little while putting her up on the center stand, that bike is heavy, I think I will put her on a diet (Modify). :whistle:
Not the first time the topic has come up:
Arrrrgh..Centerstand
The problem with KawCop center stands is that they're located relatively far away from the center of mass. Not much is going to change that, so getting one of those beasts to behave and "sit" is always gonna be a bit of a tussle...
There is, however, a method that's made it quite a bit easier for me:
1. Grip the radio carrier upright with your right hand.
2. Take hold of the left bar grip with your left hand.
3. This is important: Stand PARALLEL to the bike, facing forward so that your hips are in line with the your shock mounts, facing forward toward the windshield.
4. Get the stand tab in the heel crook of your boot, press it to the ground. Bend your knees slightly.
5. At the SAME time, straighten your leg and pull upwards and back on the radio carrier attachment with your right - your left merely guides the motion. Kind of like a one-armed "deadlift" motion.
I found that really made Kaw-dogging much easier - this way, your joints - ankle, knee, hip and lower back are in line with the relative motion and working together, not in opposition.
Took a fair amount of knee, hip and lower back pain to figure that one out... :S
Please Log in or Create an account to join the conversation.
- z1rick
- Topic Author
- Offline
- User
- Posts: 661
- Thank you received: 5
Anaheim CA
1999 KZ 100P
1974 Z1 900 Project
1977 (2) KZ 650 projects
Please Log in or Create an account to join the conversation.
- BSKZ650
- Offline
- User
- Posts: 2064
- Thank you received: 14
77 kz650, owned for over 25 years
77 ltd1000, current rider
76 kz900, just waiting
73 z1,, gonna restore this one
piglet, leggero harley davidson
SR, Ride captian, S.E.Texas Patriot Guard Riders.. AKA KawaBob
Please Log in or Create an account to join the conversation.
- Pterosaur
- Visitor
I dont have the cop bike but mine dosent seem that bad to get up on the center stand, is there a lot of weight difference between them ?
It ain't all that much heavier, depending on what all's shoehorned on to the beast, it's a matter of how far and where the weight is from the pivot point (fulcrum), and how far the fulcrum is located from the balance point (center of mass).
For example - my Vetter box weighs maybe 20 pounds (with all of my junk in it), but because of its location way above and behind the pivot, it seems like 100 when bear-wrasslin' that beast up on the center hump.
Honda did a much better job of designing center stands - try a V65 Sabre sometime - weighs as much or a little more than the average KZ, but isn't half the effort because they paid much more attention to where the stand pivot is located.
Please Log in or Create an account to join the conversation.