- Posts: 54
- Thank you received: 8
cleaning old brake fluid
- jertho
- Topic Author
- Offline
- User
Less
More
20 May 2016 13:31 #727631
by jertho
1978 kz750 twin
cleaning old brake fluid was created by jertho
I am replacing the master cylinder and brake lines with new. Also rebuilt the caliper with new seals and piston. What is the best tking to clean the old fluid out of the junction block where the lines and brake light switch hook together? Thanks
1978 kz750 twin
Please Log in or Create an account to join the conversation.
- punisher11b
- Offline
- User
Less
More
- Posts: 225
- Thank you received: 22
20 May 2016 14:31 #727639
by punisher11b
- good luck
Replied by punisher11b on topic cleaning old brake fluid
new brake fluid would probably be best to flush out all the old crud.
- good luck
Please Log in or Create an account to join the conversation.
- retterath
- Offline
- User
Less
More
- Posts: 99
- Thank you received: 9
20 May 2016 14:42 #727640
by retterath
Replied by retterath on topic cleaning old brake fluid
Denatured alcohol is the only solvent safe to use in a brake system. Anything else will make rubber parts swell.
The following user(s) said Thank You: jertho
Please Log in or Create an account to join the conversation.
- Nessism
- Offline
- Sustaining Member
Less
More
- Posts: 7547
- Thank you received: 2862
20 May 2016 14:58 #727642
by Nessism
Replied by Nessism on topic cleaning old brake fluid
There is no rubber in the junction block.
I'd take it off and shoot some brake cleaner in there. If you have a rifle brush that could be use to scrub it out as well.
BTW, nice job of updating the brake system properly.
I'd take it off and shoot some brake cleaner in there. If you have a rifle brush that could be use to scrub it out as well.
BTW, nice job of updating the brake system properly.
The following user(s) said Thank You: jertho
Please Log in or Create an account to join the conversation.
- bluej58
- Offline
- Sustaining Member
- The chrome don't get you home
Less
More
- Posts: 2484
- Thank you received: 511
21 May 2016 04:43 #727718
by bluej58
78 KZ1000 A2A
Replied by bluej58 on topic cleaning old brake fluid
What year bike are you talking about?
78 KZ1000 A2A
Please Log in or Create an account to join the conversation.
- jertho
- Topic Author
- Offline
- User
Less
More
- Posts: 54
- Thank you received: 8
21 May 2016 04:47 #727719
by jertho
1978 kz750 twin
Replied by jertho on topic cleaning old brake fluid
Thanks guys. I have the junction off of the bike so that I can do a good job of cleaning it. The rifle brush sounds like a good idea. I have one so that is what I will use. I am a firm believer in using the front brake every time I stop.
Jerry
Jerry
1978 kz750 twin
Please Log in or Create an account to join the conversation.
- wrenchmonkey
- Offline
- User
Less
More
- Posts: 568
- Thank you received: 75
21 May 2016 06:15 #727729
by wrenchmonkey
Replied by wrenchmonkey on topic cleaning old brake fluid
I just rebuilt the rear master cylinder of KZombie last evening.
Almost the entire thing was packed with hard, whitish powder from reservoir to bottom of main cylinder bore where it took a lot of working it over just to get the main piston free enough to extract from the bore. That same #6 screw extractor that I used to rebuild the front forks worked out as the best tool for this job too I love when a single-use tool has more functions!
The only thing I used was PB Blaster (which did not affect the rubber seals at all) to get the piston or parts moving again and all the hard crusty yuck just kinda fell out. Later I gave the whole thing a vigorous bath in soapy water to flush all the passages.
I did have to invent a tool for one passage which went from the larger port diagonally down into the main bore. Turned out a 4" piece of coaxial cable was like perfect!
Almost the entire thing was packed with hard, whitish powder from reservoir to bottom of main cylinder bore where it took a lot of working it over just to get the main piston free enough to extract from the bore. That same #6 screw extractor that I used to rebuild the front forks worked out as the best tool for this job too I love when a single-use tool has more functions!
The only thing I used was PB Blaster (which did not affect the rubber seals at all) to get the piston or parts moving again and all the hard crusty yuck just kinda fell out. Later I gave the whole thing a vigorous bath in soapy water to flush all the passages.
I did have to invent a tool for one passage which went from the larger port diagonally down into the main bore. Turned out a 4" piece of coaxial cable was like perfect!
Please Log in or Create an account to join the conversation.
- davido
- Offline
- User
Less
More
- Posts: 1584
- Thank you received: 292
21 May 2016 07:30 #727737
by davido
www.kzrider.com/forum/11-projects/594313-csr1000-project-build
CB550 (1978)
CB500/4 (1972)*
KZ1000CSR (1981)
XT 600E (1999)
TDM900 (2003)
Replied by davido on topic cleaning old brake fluid
When I got my ZXR brakes from the postie,I drained them and dumped them straight in a bucket of soapy water. Let them sit for a while then give them a good scrub. For getting into the very small holes,dental brushes are usefull.
www.kzrider.com/forum/11-projects/594313-csr1000-project-build
CB550 (1978)
CB500/4 (1972)*
KZ1000CSR (1981)
XT 600E (1999)
TDM900 (2003)
Please Log in or Create an account to join the conversation.