KZ400 Exhaust Swap

More
17 Sep 2024 18:51 #904404 by ThatYeti
KZ400 Exhaust Swap was created by ThatYeti
Finally managed to find a used original exhaust for my bike to replace the super loud franken exhaust that it came to me with, after having zero success quieting it down with different replacement baffles.

Question now is what all I might need to swap in the new pipes. Do I need to replace any gaskets? Any tips on getting the old pipes off the studs without breaking anything? And are the pipes I got the style that caused oil leaks due to the crossover pipe? If so should I cap those off? 

Looking to swap everything all at once so if I need more than the missing clamp for the crossover pipe I want to order it ahead of time.

Thanks as always
 

'76 KZ400

Please Log in or Create an account to join the conversation.

  • Wookie58
  • Away
  • Moderator
More
18 Sep 2024 02:06 #904420 by Wookie58
Replied by Wookie58 on topic KZ400 Exhaust Swap
You should replace the gaskets between the pipe and cylinder head, you can use a small amount of exhaust sealer on the balance pipe. With the studs you should soak them with penetrating fluid and repeat over a couple of days (not when hot as penetrating fluid is flammable) when removing the nuts - if they go tight wind them back on and clean the stud with a wire brush, apply penetrating fluid and wind off again (keep repeating this process until the nuts are off)
The following user(s) said Thank You: ThatYeti

Please Log in or Create an account to join the conversation.

More
18 Sep 2024 04:06 #904421 by ThatYeti
Replied by ThatYeti on topic KZ400 Exhaust Swap
Thanks, I'll see about finding gaskets along with the metal clamp, but there's nothing I needed to worry about in keeping that crossover pipe?

'76 KZ400

Please Log in or Create an account to join the conversation.

  • Wookie58
  • Away
  • Moderator
More
18 Sep 2024 04:37 #904422 by Wookie58
Replied by Wookie58 on topic KZ400 Exhaust Swap

Thanks, I'll see about finding gaskets along with the metal clamp, but there's nothing I needed to worry about in keeping that crossover pipe?
Not that I am aware of
The following user(s) said Thank You: ThatYeti

Please Log in or Create an account to join the conversation.

More
18 Sep 2024 05:31 #904424 by ThatYeti
Replied by ThatYeti on topic KZ400 Exhaust Swap
Any idea which gaskets are a better option? Seeing both aluminum and copper gaskets in searching, mostly seeing them on eBay and oddly seeing both in OEM packaging.

'76 KZ400

Please Log in or Create an account to join the conversation.

  • Wookie58
  • Away
  • Moderator
More
18 Sep 2024 05:35 #904425 by Wookie58
Replied by Wookie58 on topic KZ400 Exhaust Swap

Any idea which gaskets are a better option? Seeing both aluminum and copper gaskets in searching, mostly seeing them on eBay and oddly seeing both in OEM packaging.
I will leave that for the 400 guys on here to share their experience, what part number does CMNSL or Partzilla list for your specific bike ?
The following user(s) said Thank You: ThatYeti

Please Log in or Create an account to join the conversation.

More
18 Sep 2024 07:36 #904427 by ThatYeti
Replied by ThatYeti on topic KZ400 Exhaust Swap
Partzilla doesn't have anything for it and the only one I found at a retailer was Z1 who shows it out of stock but it's the aluminum gaskets with part number OEM Ref: 11060-1242

'76 KZ400
The following user(s) said Thank You: Wookie58

Please Log in or Create an account to join the conversation.

  • gd4now
  • Offline
  • User
  • Denco where did you go?
More
18 Sep 2024 10:31 #904430 by gd4now
Replied by gd4now on topic KZ400 Exhaust Swap
According to Kawasaki site the exhaust pipes for the 76 and 77 models did not have the cross over pipe, but it does show this pipe for the 78 model year.  Which does show the clamps and gaskets it used.  www.kawasaki.com/en-us/owner-center/parts/142603/1978/KZ400-B1

 

1977 KZ650 B1
Pods and Denco header


OLD KAW OWNERS SMILE ALOT

The following user(s) said Thank You: ThatGPzGuy, ThatYeti

Please Log in or Create an account to join the conversation.

More
18 Sep 2024 11:27 #904431 by ThatYeti
Replied by ThatYeti on topic KZ400 Exhaust Swap
Guess the new to me exhaust must be from a slightly newer bike, but holding it up to the pipes on it seems like it'll fit just fine. Do I need to worry about that crossover pipe? Saw an old post talking about how an early version that seemed to run through the engine caused leaks. This one seems like it would run underneath but I guess I could see about welding those holes shut if it'll be problematic. 

'76 KZ400

Please Log in or Create an account to join the conversation.

  • Wookie58
  • Away
  • Moderator
More
18 Sep 2024 13:00 #904432 by Wookie58
Replied by Wookie58 on topic KZ400 Exhaust Swap

Guess the new to me exhaust must be from a slightly newer bike, but holding it up to the pipes on it seems like it'll fit just fine. Do I need to worry about that crossover pipe? Saw an old post talking about how an early version that seemed to run through the engine caused leaks. This one seems like it would run underneath but I guess I could see about welding those holes shut if it'll be problematic. 
I believe what you are referring to was a passage in the head (happy to be corrected) the balance pipe in the exhaust helps torque and smooth running by balancing both cylinders - I'm not aware of any downside (probably why the factory fitted it on later models)
The following user(s) said Thank You: ThatYeti

Please Log in or Create an account to join the conversation.

More
19 Sep 2024 04:11 #904447 by ThatYeti
Replied by ThatYeti on topic KZ400 Exhaust Swap
Any opinions on whether the copper or aluminum gaskets (crush washers) are the way to go? And any idea if one meant for a car would work, so long as it's the right size? Was hoping to get the exhaust on soonish but if I have to order the washers it looks like it's going to be weeks before I'll get them.

'76 KZ400

Please Log in or Create an account to join the conversation.

  • Wookie58
  • Away
  • Moderator
More
19 Sep 2024 04:48 #904449 by Wookie58
Replied by Wookie58 on topic KZ400 Exhaust Swap
Cars don't use this type of sealing washer, personally I think either aluminium or copper (which ever is easily available) should do the trick (it simply needs to crush and fill any gaps between the header and exhaust port)

Please Log in or Create an account to join the conversation.

Powered by Kunena Forum