76 KZ900

More
19 Mar 2023 10:05 #881778 by mvent
Replied by mvent on topic 76 KZ900
Pulled carbs again, blew them out with compressed air, pilot jets clear #4 head pipe not getting hot, #3 better but not close to cylinder  1 and 2. temp at spark plugs are pretty close on all 4. Switched plug wire from 1 and 4 no change, switched out spark plugs no change, hot compression on #4 150, other 3 between 135-150. I guess this narrows it down to carburetor ? Float height same on all carbs and all getting fuel.  Ultra sonic next. Any ideas ?


76 KZ900
76 XLCH
78 KZ1000
04 FLSTFI 120 ci

Please Log in or Create an account to join the conversation.

More
19 Mar 2023 11:18 #881782 by Mikaw
Replied by Mikaw on topic 76 KZ900
You make a very confusing comment if I read correctly. You say the IR temps are very similar at the spark plugs, but you have extreme temp difference at the down (head) tube. This doesn’t seem possible. Is it possible you have a blockage in the down tube. Critter nest? I bought an once engine that had short 6-8 inch sections of down tubes affixed and mice had called up into the open tube and built nest in one of them.

1976 KZ 900 A4 kzrider.com/forum/11-projects/613548-1976-kz-900-a4
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.

Please Log in or Create an account to join the conversation.

More
19 Mar 2023 11:46 #881783 by mvent
Replied by mvent on topic 76 KZ900
Mikaw funny you said that it did cross my mind but I thought between the exhaust heat and pressure it would have blown it out. 


76 KZ900
76 XLCH
78 KZ1000
04 FLSTFI 120 ci

Please Log in or Create an account to join the conversation.

More
19 Mar 2023 11:55 #881784 by Mikaw
Replied by Mikaw on topic 76 KZ900
Not sure what else could cause such a temp differential between the plug and the down tube. 

1976 KZ 900 A4 kzrider.com/forum/11-projects/613548-1976-kz-900-a4
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.

Please Log in or Create an account to join the conversation.

  • Scirocco
  • Offline
  • Premium Member
  • Never change a running system
More
19 Mar 2023 14:45 - 19 Mar 2023 14:56 #881794 by Scirocco
Replied by Scirocco on topic 76 KZ900
Remove the bleeder tubes under the main jets and give them a clean. Compressed air is not a cleaning medium!Did you inspect and set the pilot air mixture screws to 1 1/2 - 1 3/4 turns out? A broken air mixture screws tip can made your day!Are the carbs mechanical/vaccum synced? 

 
 
 
 
Last edit: 19 Mar 2023 14:56 by Scirocco.
The following user(s) said Thank You: Nessism, howardhb

Please Log in or Create an account to join the conversation.

More
19 Mar 2023 15:52 #881795 by mvent
Replied by mvent on topic 76 KZ900
Scirocco, all above mentioned has been done air screws are 1 1/2 turns out. Mechanically synched for now. Thanks for the suggestions. These are Z1b carbs, are pilot jets supposed to have o rings? none of these do.


76 KZ900
76 XLCH
78 KZ1000
04 FLSTFI 120 ci

Please Log in or Create an account to join the conversation.

  • Scirocco
  • Offline
  • Premium Member
  • Never change a running system
More
19 Mar 2023 16:21 #881798 by Scirocco
Replied by Scirocco on topic 76 KZ900
These are air/fuel mixer screws were the tip was broken and stuck in the carb body.

 
 
The following user(s) said Thank You: mvent, sf4t7, howardhb

Please Log in or Create an account to join the conversation.

More
19 Mar 2023 19:28 #881807 by Mikaw
Replied by Mikaw on topic 76 KZ900
Here this will help with item terms. There are no ORings on the pilot jet #21, non on the main jet emulsion tube/ jet holder #20, nor on the pilot air adjustment screw #23.

 

1976 KZ 900 A4 kzrider.com/forum/11-projects/613548-1976-kz-900-a4
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.
The following user(s) said Thank You: mvent, Scirocco

Please Log in or Create an account to join the conversation.

More
20 Mar 2023 07:39 - 20 Mar 2023 09:41 #881816 by mvent
Replied by mvent on topic 76 KZ900
This is a picture into exhaust port of #4 cylinder 


76 KZ900
76 XLCH
78 KZ1000
04 FLSTFI 120 ci
Last edit: 20 Mar 2023 09:41 by Street Fighter LTD.

Please Log in or Create an account to join the conversation.

More
20 Mar 2023 07:47 #881817 by Mikaw
Replied by Mikaw on topic 76 KZ900
Looks like it’s been running rich or burning some oil, but I don’t see anything “Abbynormal”. 

1976 KZ 900 A4 kzrider.com/forum/11-projects/613548-1976-kz-900-a4
1976 KZ 900 B1 LTD
1978 KZ 1000 B2 LTD
1980 KZ 750 E1
Kowledge Speaks, But Wisdom Listens.
Jimi Hendrix.

Please Log in or Create an account to join the conversation.

More
20 Mar 2023 07:50 #881818 by Wookie58
Replied by Wookie58 on topic 76 KZ900

Pulled carbs again, blew them out with compressed air, pilot jets clear #4 head pipe not getting hot, #3 better but not close to cylinder  1 and 2. temp at spark plugs are pretty close on all 4. Switched plug wire from 1 and 4 no change, switched out spark plugs no change, hot compression on #4 150, other 3 between 135-150. I guess this narrows it down to carburetor ? Float height same on all carbs and all getting fuel.  Ultra sonic next. Any ideas ?
Have you tried switching the actual coils ?

Please Log in or Create an account to join the conversation.

More
20 Mar 2023 13:50 #881834 by mvent
Replied by mvent on topic 76 KZ900
Wookie I have not, switching wires between 1 and 4 then spark plugs without change my assumption was that would eliminate any electrical problems with coils, wires and spark plugs.


76 KZ900
76 XLCH
78 KZ1000
04 FLSTFI 120 ci

Please Log in or Create an account to join the conversation.

Powered by Kunena Forum